Download for T2600G-28TS
- Product Overview
2.0_1500543408797k.jpg)
MIBs Files
|
T2600G-28TS(UN)_V2_170928_MIB |
Download | |
|---|---|---|
| Published Date: 2017-09-28 | Language: English | File Size: 183.07 KB |
Operating System: Win2000/XP/2003/Vista/7/8/8.1/10 |
||
|
|
||
|
T2600G-28TS(UN)_V2_170118_MIB |
Download | |
|---|---|---|
| Published Date: 2017-01-18 | Language: English | File Size: 189.55 KB |
Operating System: Win2000/XP/2003/Vista/7/8/8.1/10/Mac/Linux |
||
|
|
||
802.1X Client
|
TP-LINK_802.1X_Client_Software |
Download | |
|---|---|---|
| Published Date: 2017-09-05 | Language: English | File Size: 5.5MB |
Operating System: Win2000/XP/2003/Vista/7/8/8.1/10 |
||
|
|
||
FAQs
- How to configure LACP on our Smart/ Managed Switch
- How to Block Unknown Devices to Access the Switch by Using IP Source Guard
- Why the firmware version does not change after upgrading in T Series switches?
- How to configure the default gateway of the smart and managed switches using the old GUI
- What is the Console Cable and the line sequence of it?
- How to build a Campus Network using TP-LINK products
- The difference between the Voice VLAN feature and Auto VOIP feature
- What should I do if I cannot access the web management page of my TP-Link switch?
- Do you still have any doubt about the effect of QoS on the Switch of TP-Link?
- How to block an illegal client with Certain IP address from getting access to the network using TP-Link Managed Switches
- How to access TP-Link JetStream Managed Switch via the Console port
- How to configure 802.1Q VLAN on L2 Managed switches using the old GUI
- How to Configure Port Isolation Function on Our Layer 2 Manage switches through Web Browser
- How to limit the port rate of the incoming traffic via ACL function
- How to test the Jumbo Frame pass-through feature on TP-Link switches
- How to build up a multi-nets network via Multi-Nets NAT feature on TP-Link router with L2+/L3 switches
- How to change the IP address of the smart and managed switches using the old GUI and CLI
- How to configure MAC ACL on Smart/Managed switch
- How to configure the DHCP Relay in TP-Link Switch
- How to change the IP address of the smart and L2 managed switches using the new GUI and CLI
- How to configure Voice VLAN to optimize the transmission of voice traffic on TP-Link Smart and Managed Switches using the new GUI
- How to configure OpenSSH 7.0(and above) to login smart and managed switches?
- The nodes that TP-Link T1600/T2600 series switch use to display the CPU and Memory utilization through SNMP
- How to configure Extended IP ACL
Firmware
A firmware update can resolve issues that the previous firmware version may have and improve its current performance.
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty.
How to find the hardware version on a TP-Link device - Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it's recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It's recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
T2600G-28TS(UN)_V2_170928 |
Download | |
|---|---|---|
| Published Date: 2017-09-28 | Language: English | File Size: 10.58 MB |
|
Modifications and Bug Fixes: Fixed the problem that DHCP request will be intercepted when enable IP Source Guard;Fixed the problem that incorrect SNMP typing might hang the switch; Enhanced the DHCP relay functions; Enhanced the QoS function. Notes: For T2600G-28TS(UN) V2 |
||
To Use Third Party Firmware In TP-Link Products
Some official firmware of TP-Link products can be replaced by the third party firmware such as DD-WRT. TP-Link is not obligated to provide any maintenance or support for it, and does not guarantee the performance and stability of third party firmware. Damage to the product as a result of using third party firmware will void the product's warranty.
Open Source Code For Programmers (GPL)
Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License ("LGPL"). You may use the respective software condition to following the GPL licence terms.
You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-Link products for direct download and further information, including a list of TP-Link software that contain GPL software code under GPL Code Center.
The respective programs are distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the respective GNU General Public License for more details.