How to use Tapo Solar Panel with Tapo Battery Security Cameras
15555
Tapo Solar Panel |
|
|
✅ Non-Stop Power Supply with Flexible Installation ✅ High-Efficiency Solar Charging ✅ Flexibly Adjustable Angle for Sufficient Sunlight ✅ IP65 Weatherproof |
|
|
|
|
|
Compatible Cameras: Tapo C410 / TC82 Tapo C425 / TC85 Tapo C420 Tapo C400 |
Compatible Cameras with Micro USB Port: Tapo C425 V1.0/V1.20 TC85 V1.0/V1.20 Tapo C420 V1.0/V1.20 Tapo C400 |
Step 1: Position the Solar Panel
The position and tilt angle of the solar panel greatly affect the solar efficiency.
1. Choose a location where the solar panel gets the most sunlight throughout the year.
2. Position the panel south-facing in the Northern Hemisphere or north-facing in the Southern Hemisphere. The recommended tilt angle between the panel and the horizontal ground is 35° ~ 45°.
3. Regularly wipe the panel to remove dust and debris.
Step 2: Mount the Solar Panel
*Here we take Tapo A201 as an example.
1. Drill Holes
Stick the mounting template to a solid and level wall surface. Drill three screw holes according to the template.
2. Mount Bracket
Insert three wall anchors into the holes and use the mounting screws to affix the solar panel bracket over the anchors.
3. Install Solar Panel
Slide the solar panel onto the mounting bracket until it clicks into place.
4. Adjust Angle
Loosen the adjustable screw, tilt the solar panel to adjust the angle, and then tighten the adjustable screw.
The recommended tilt angle between the panel and the horizontal ground is 35° ~ 45°.
5. Install Screw Caps & Base Cover
Insert two screw caps into the screw holes until flush, then install the base cover.
Screw Cap Orientation 
1. Drill Holes
Stick the mounting template to a solid and level wall surface. Drill three screw holes according to the template.
2. Install Camera Bracket
Secure the camera bracket to the solar panel bracket using two screws.
The third hole below is for securing the solar panel bracket.
3. Mount Solar Panel Bracket
Insert three wall anchors into the holes and use the mounting screws to affix the solar panel bracket over the anchors. Then, insert two screw caps into the upper screw holes until flush.
Screw Cap Orientation 
4. Install Solar Panel
Slide the solar panel onto the mounting bracket until it clicks into place.
5. Adjust Angle
Loosen the adjustable screw, tilt the solar panel to adjust the angle, and then tighten the adjustable screw.
The recommended tilt angle between the panel and the horizontal ground is 35° ~ 45°.
6. Install Camera & Adjust Angle
Install the camera onto the bracket and adjust the camera angle as per the camera's guide.
Note: Ensure the camera is securely attached to the camera bracket by tightening the bottom screw.
1. Drill Holes
Stick the mounting template to a solid and level wall surface. Drill three screw holes according to the template.
2. Mount Bracket
Insert three wall anchors into the holes and use the mounting screws to affix the solar panel bracket over the anchors. Then, insert two screw caps into the upper screw holes.
3. Install the Solar Panel
Slide the solar panel onto the mounting bracket until it clicks into place.
4. Adjust Angle
Loosen the adjustable screw, tilt the solar panel to adjust the angle, and then tighten the adjustable screw.
The recommended tilt angle between the panel and the horizontal ground is 35° ~ 45°.
5. Install Camera & Adjust Angle
Install the camera onto the bracket and adjust the camera angle as per the camera's guide.
Note: Ensure the camera is securely attached to the camera bracket by tightening the bottom screw.
Step 3: Connect Solar Panel to the Camera
The gasket protects your camera from exposed moisture and dust that may damage the camera. Choose one based on your camera’s charging port.
For detailed instructions, please refer to How to connect Tapo Solar Panel to compatible Tapo devices with proper Waterproof Gasket
Questa faq è utile?
Your feedback helps improve this site.
