Download for Deco M4(2-pack)
Vx.0=Vx.6/Vx.8/Vx.9(eg:V1.0=V1.6/V1.8V1.9)
Vx.x0=Vx.x6/Vx.x8/Vx.x9 (eg:V1.20=V1.26/V1.28/1.29)
Vx.30=Vx.32/Vx.33 (eg:V3.30=V3.32/V3.33)
- Product Overview
FAQs
- The internet connection is unstable or suddenly stops working when connected to the Deco network?
- How to set up Deco to work in Access Point mode
- How to log into the web-based interface of my Deco
- How to enable the TP-Link Router Skill in the Alexa app
- How to use firmware recovery if the Deco become brick
- What is the TP-Link Router Alexa Skill and how do I use it?
- Deco Setup Walkthrough(For Deco X20/X60/X90/P9/M4/S4/E4/W2400 etc)
- Frequently asked questions about TP-Link Home Mesh Wi-Fi
- What’s the difference between Access Point mode and Router mode on the Deco?
- Troubleshooting Slow Internet Speed with Deco Devices
- How to Configure PPTP/L2TP VPN Connection on the Deco
- How to set up Port Forwarding feature on the Deco
- How many Deco units do I need? Are they all the same?
- How to change the Wireless Settings on your Deco app
- How to control the TP-Link router/Deco with Google Assistant
- How to Configure MAC Clone on Deco if Deco fails to connect to the internet
- Why did I receive a new device connection alert when a known device joined the network?
- How do I know which Deco my client is connected to?
- Cannot connect to Deco Wi-Fi
- How to Create a New Network in the Deco App
- How can I reset or reboot my Deco Whole-Home Wi-Fi System?
- How to configure the Connection Alerts feature on the Deco app
- How to change the name of the client on the Deco app
- How to change the device name of Deco
- How to set up an IPv6 internet connection on my Deco
- How to configure VLAN ID for your internet connection on Deco
- How to change LAN IP address of Deco
- How to change DNS server settings on my Deco
- How to set up QoS on the Deco
- How to change Notification settings of Deco
- General questions about the AI-Driven Mesh feature
- Why my clients don't roam/connect to the nearest Deco node?
- General question about the Wi-Fi range of Deco
- How to change Time settings on the Deco
- Fail to log into the web management page of Deco
- Why is a device displayed as an unknown device on the Deco app？
- What should I do if Wi-Fi calling cannot work through TP-Link wireless router?
- How to Boost Your Wi-Fi Signal
- What are the differences between different models of Deco?
- Can I use Deco with my existing router?
- Why my clients fail to connect to the Deco Wi-Fi when Fast Roaming is enabled?
- How to Link your TP-Link Router to Google Assistant
- What do the different LED colors meaning of Deco?
Firmware
A firmware update can resolve issues that the previous firmware version may have and improve its current performance.
To Upgrade
IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process
- Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
- Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty.
How to find the hardware version on a TP-Link device - Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
- To avoid wireless disconnect issue during firmware upgrade process, it's recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
- It's recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
- Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
|
Deco M4(EU)_V4_1.1.1 Build 20230201 |
Download | |
|---|---|---|
| Published Date: 2023-03-03 | Language: Multi-language | File Size: 13.42 MB |
|
Improvement: |
||
|
Deco M4(EU)_V4_1.1.0 Build 20230112 |
Download | |
|---|---|---|
| Published Date: 2023-02-09 | Language: Multi-language | File Size: 13.42 MB |
|
New features: Notes: |
||
To Use Third Party Firmware In TP-Link Products
Some official firmware of TP-Link products can be replaced by the third party firmware such as DD-WRT. TP-Link is not obligated to provide any maintenance or support for it, and does not guarantee the performance and stability of third party firmware. Damage to the product as a result of using third party firmware will void the product's warranty.
Open Source Code For Programmers (GPL)
Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License ("LGPL"). You may use the respective software condition to following the GPL licence terms.
You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-Link products for direct download and further information, including a list of TP-Link software that contain GPL software code under GPL Code Center.
The respective programs are distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the respective GNU General Public License for more details.