How to configure and install Deco X50-Outdoor properly

Configuration Guide
Updated 09-21-2023 07:34:04 AM 39823
This Article Applies to: 

Deco X50-Outdoor can provide WiFi coverage for your outdoor space. We will guide you through step by step installing it correctly to maximize its performance.

Most customers add Deco X50-Outdoor as a satellite Deco to an existing Deco network, so we are here using this situation as a demonstration (although X50-Outdoor can also be used as Main Deco).

Here is also a video demonstration:

1. Take Deco X50-Outdoor near any indoor Deco unit first.

2. Power Deco X50-Outdoor

1) Remove the base plate from Deco X50-Outdoor (store carefully to avoid losing base plate and screws).

Video:

2) Power on the Deco X50-Outdoor through method 1 or 2.

Method 1: through IEEE 802.3at PoE switch or IEEE 802.3at PoE adapter

Method 2: through 100-240V~50/60Hz 0.5A AC power supply. To power the Deco X50-Outdoor at outdoor place using AC power, there needs to be an outdoor waterproof socket near the Deco X50-Outdoor installation location. And please protect the AC outlet and power cord from rain.

At the indoor configuration stage, power up X50-outdoor either way. Afterward, based on your personal situation, choose to use PoE or AC power for outdoor usage.

3. Configure Deco X50-Outdoor with the Deco App

You can refer to the following FAQ to add Deco X50-Outdoor to the existing network.

How to add an additional unit to your Deco network

During the configuration, please place the Deco X50-Outdoor near existing Deco devices to ensure the Deco X50-Outdoor can be quickly discovered and added to the network, and no need to reinstall the base plate at moment.

After completing the configuration, you can temporarily unplug the power supply, take Deco X50-Outdoor, base plate, installation accessories, and tools to the desired outdoor area.

4. Select a suitable installation location

Installation location can significantly impact performance and coverage range. Here are some suggestions when choosing the right location:

1) Ensure a stable and secure power supply at the installation location. If using PoE, consider the reach of the Ethernet cable. If using AC power, check for nearby outdoor waterproof outlets that can provide power.

2) If X50-Outdoor and the front-end Deco are connected wirelessly, it is recommended to keep the distance between X50-Outdoor and the front-end Deco within 33 feet (or 10 meters) to ensure X50-Outdoor receive good signal from the front-end Deco, no more than 50 feet (or 15 meters). It is preferable to place the front-end Deco near a window to minimize the obstacles between it and the X50-Outdoor in the outdoor. If X50-Outdoor and the front-end Deco are connected via wire, then there is no such restriction.

3) It is recommended to install X50-Outdoor at the center of the target area where you want to expand the WiFi coverage to evenly cover the entire area.

4) The recommended installation height is 0 ~ 8m (0~25feet).

5) There should be a clear line of sight between X50-Outdoor and the area to be covered. Buildings, trees, or walls can weaken the signal strength and limit the coverage range.

6) Try to stay away from potential sources of WiFi interference, such as neighboring WiFi networks, high-voltage power lines, electronic devices, and appliances.

7) It is recommended to install X50-Outdoor in the location where receive less rainwater or direct sunlight.

All installations will vary depending on the environment. So it's always good to perform pre- and post-installation site surveys, measured to your desired data rates, as is the case when configuring any wireless extender or Access Point.

5. Mount X50-Outdoor

1)After selecting the installation location, please insert the Ethernet cable and power cord according to your own situation.

• PoE-powered: Ethernet cable only

• AC-powered: Wireless: Power cord only ;Wired: Ethernet cable + Power cord

2) Install the base plate back to waterproof X50-Outdoor.

Currently we recommend two methods:

1. Pole Mounting

1)Lead the end of the pole mounting strap through the back of the Deco.

2)Position the Deco and wrap the pole mounting strap around the pole. Feed the end through the screw-block and tighten the strap until the Deco is secure.

Note: The Deco can only be used in upright direction. Please do not mount Deco X50–Outdoor in an inverted or side-standing matter. Incorrect mounting may result in the device failing to maintain its waterproof status.

2. Wall Mounting

1) Place the mounting bracket in the right position. Mark two positions for the screw holes. Drill two 6 mm diameter holes for the screws at the marked positions.

2. Insert the plastic wall anchors into the 6 mm diameter holes. Align the mounting bracket to the plastic wall anchors and drive the self-tapping screws into the anchors through the mounting bracket.

3. Align the mounting tabs on the back of the Deco with the slot of the mounting bracket. Push and slide the Deco downward until it locks into place.

Note: The Deco can only be used in upright direction. Please do not mount Deco X50–Outdoor in an inverted or side-standing matter. Incorrect mounting may result in the device failing to maintain its waterproof status.

Now you finish the installation process of X50-Outdoor.

Get to know more details of each function and configuration please go to Download Center to download the manual of your product.

Related FAQs

Is this faq useful?

Your feedback helps improve this site.

Community

TP-Link Community

Still need help? Search for answers, ask questions, and get help from TP-Link experts and other users around the world.

Visit the Community >

From United States?

Get products, events and services for your region.