Bu web sitesi çerezler içermektedir. Çerezlerin kullanım amacı ve 6698 sayılı Kişisel Verilerin Korunması Kanunu uyarınca kişisel verilerin kullanımına dair şirket politikası hakkında daha fazla bilgi için buraya basınız. Tekrar Gösterme
What if the wires are too short, soft, or stiff to connect when installing Tapo floodlight camera?
Further Assistance
Güncellendi05-21-2024 01:42:07 AM8283
Bu Makalenin Geçerliliği:
TC55 , Tapo C720 , TC53
Recent updates may have expanded access to feature(s) discussed in this FAQ. Visit your product's support page, select the correct hardware version for your device, and check either the Datasheet or the firmware section for the latest improvements added to your product. Please note that product availability varies by region, and certain models may not be available in your region.
When installing the Tapo floodlight camera on your existing junction box or with existing electrical wires, you may encounter the following situations:
• The wires from the junction box or wall are too short to connect.
• The wires from the junction box or wall are too soft to connect.
• The wires from the junction box or wall are too stiff to connect.
To deal with these situations, you can use extension wires and wire nuts/connectors.
When you use click flow connectors or a connector strip as below, please use the heat shrink tubes to cover the connectors and extension wires outside (at least 8 mm).
Note: If it is too difficult for you, please consult a licensed electrician.
If you use wires nuts, please refer to the following steps.
Align the Neutral wire (usually white/blue) with the white extension wire ends.
Place one wire nut connector over the wires. Twist the wire nut clockwise to tighten the wires.
Repeat the above steps to extend the Line wire (usually black/brown/red) using the black extension wire and another wire nut.
When installing on the existing junction box:
When installing with existing electrical wires:
Use two heat shrink tubes to cover the wire nuts and wires outside (at least 8 mm).
Follow the Quick Start Guide to wire the bracket and install the floodlight camera. Do not turn on the circuit breaker before completing the installation.
Bu SSS faydalı mı?
Your feedback helps improve this site.
Bu makaleyle ilgili sorununuz nedir?
Üründen memnun kalmadım
Çok Karışık
Karışık Başlık
Bu benim için geçerli değil
Çok Belirsiz
Diğer
Teşekkürler
We appreciate your feedback. Click here to contact TP-Link technical support.
Bu web sitesi çerezler içermektedir. Çerezlerin kullanım amacı ve 6698 sayılı Kişisel Verilerin Korunması Kanunu uyarınca kişisel verilerin kullanımına dair şirket politikası hakkında daha fazla bilgi için buraya basınız. Tekrar Gösterme
Bu web sitesi çerezler içermektedir. Çerezlerin kullanım amacı ve 6698 sayılı Kişisel Verilerin Korunması Kanunu uyarınca kişisel verilerin kullanımına dair şirket politikası hakkında daha fazla bilgi için buraya basınız. Tekrar Gösterme
Temel Çerezler
Bu çerezler, web sitesinin çalışması için gereklidir ve sistemlerinizde devre dışı bırakılamaz.
Analiz çerezleri, web sitemizin işlevselliğini geliştirmek ve uyarlamak için web sitemizdeki faaliyetlerinizi analiz etmemizi sağlar.
Pazarlama çerezleri, ilgi alanlarınıza uygun bir profil oluşturmak ve size diğer web sitelerinde alakalı reklamlar göstermek için reklam ortaklarımız tarafından web sitemiz aracılığıyla ayarlanabilir.